Polyethylene Film Anticorrosion Tape Anti corrosion Coating for Underground Steel Pipe Coating - T-140, T-150, T-165, T-180, T-1100, T-1130
|Material: PE||Use: Masking||Adhesive Side: Single Sided||Adhesive: Rubber,Butyl Rubber|
|Adhesive Type: Hot Melt,Pressure Sensitive,Water Activated||Feature: Antistatic||Design Printing: Offer Printing||Place of Origin: Zhejiang China (Mainland)|
|Brand Name: Ningbo Ideal||Model Number: T-140, T-150, T-165, T-180, T-1100, T-1130||Usage: Polyethylene Film Anticorrosion Tape Anti corrosion Coating for Pipe||Backing: Polyethylene PE HDPE LDPE MDPE|
|Thickness:: 0.38 to 1.27mm||Width:: 2, 3, 4, 6, 9,12 Inch||Length:: 61 Meter||Certification: ISO9001:2008|
|Type: Adhesive Tape||Adhesive Tape Type: Single-Side Tape||Other Names: Anti corrosion Tape,Anticorrosion Tape,Polyethylene Tape|
1.INTRODUCTION TO PRODUCTS:
Inner Tape ( Polyethylene Film Anticorrosion Tape Anti corrosion Coating for Underground Steel Pipe Coating )System Description:
The T-100 series is Cold Applied Corrosion Protection Tape coating systems for the anticorrosion of underground, underwater, and overhead pipelines. Butyl Rubber Adhesive is a key in ground performance characteristic coupled with the low and high density polyethylene backing. This kind of tape can be applied by hand or with a wrapping machine.
- Conformable to irregular shapes.
- No release liner.
- Established in ground history.
- Complies with AWWA (American Water Works Association) C-214 standard.
- Compatible with general coating systems.
T-100 Inner Tape (Anticorrosion Tape,Corrosion Protection Tape, Anti corrosion Tape, Corrosion Tape, Corrosion Tapes) series Coating Systems with AWWA C-214 Standard:
Type of Anticorrosive tape:
(ASTM D 1000)
2, 3, 4, 6, 9,12 Inch
Peel Adhesion to Prime Pipe:
(ASTM D 1000)
165 oz/in, 18N/10mm
Cathodic Disbandment: (ASTM G8)
0.25 in radius 6.4 mm
Water Vapor Transmission Rate:
Water Absorption: (ASTM D570)
Volume Resistively: (ASTM E257)
2.5 X 1012ohm·cm
Dielectric Strength: (ASTM D 149)
(Normal in Ground Service)
-30 to 160oF, -34 to 71oC
2. POLYETHYLENE PE TAPE & PRIMER APPLICATIONS:
Rust Removal > Priming> Inner Tape & Outer Tape Wrapping
2.1 Rust Removal
Steel Surface needs treating. Its quality shall reach Sa2 or St3 grade as prescribed in GB8923-88 Pre-paint Steel Surface Rust Grade and Rust-removal Grade, and it shall be dust-free.
Primer shall be stirred well before painting. An even film of primer is painted on the steel surface that is rust-removed completely and dust-free. After the primer dries up (one may feel no sticky). The steel pipe can be wrapping with tape (it usually takes 3 to 5 minutes). The primer dosage usually amounts to 80 to 100g / m2.
2.3 Inner Tape (Anti corrosion Tape) & Outer Tape (Protection Tape) Wrapping
The steel pipe that is painted with primer is wrapping with tape by means of suitable devices or tools as per joint needs, and wraps the inner tape and then wraps the outer tape. Tape tensibility can be 10 to 20 N / cm. The overlapped length between beginning and end of an adhesive tape shall be no less than 1/4 circumference of the steel pipe and the total length of adhesive tape shall be no less than 100mm. each film shall be paralleled, and must not be twisted and rumpled.
3. QUALITY CONTROL QA/QC:
Mechanical Test> Plastic Test> Electric Test> Chemical Analysis> Heat Aging Test
Covered Tape by Polyethylene sheet,and then loaded to carton.
Logistic Department loading and transportation.
|Packaging Detail:Covered Polyethylene Film Anticorrosion Tape Anti corrosion Coating for Underground Steel Pipe Coating by polyethylene PE Release Liner and then loaded to carton......|
|Delivery Detail:45 days|