Sublimation mug heat press machine - DS-mug-2

Feature
Digital temperature indicator
Automatic temperature constant
Even pressure heat-resistant material remains stable up to 400 °C
Automatic baking time control
Pressure adjustable
Full mug surface heat transfer print

Specification
Voltage 220V/110V
Power 400W
Temperature range 0°C- 400°C
Time control range 0 s to 600s
Weight 8KG
Packing size: 300 X 300 X 230 mm

Opearation
1,Place a shaped mug, close the handle with appropriate pressure and then plug the power;
Caution! The machine must to be protective earthing properly before operating.
Avoid excessive pressure.
2,Cut the picture size to be large as the mug surface and then put it to the mug by adhesive tape.
3,Setting the temperature to an appropriate (between 180°C- 200°C) by turning the temperature knob;
4,Setting appropriate time, approximate 30 seconds, the temperature rising time is 2 to 4 minutes;
5,Place the picture-wraged mug, close the handle and then turn on the power, red indicator lighting;
Caution! The size of picture should be large enough to cover the whole mug surface to avoid singe and impress.
6,The machine shall start the timer automatically and enter the status of constant temperature when the temperature rises to the setting degree;
7,Release the handle when the buzzer rings and take out the mug;
Get rid of the picture paper 3 seconds after the mug to be took out from the machine.
Caution! For protecting the heating mat, place the shaped mug all the time and close the handle when the machine is not being used.
Another piece of paper should be used to cover the mug surface to avoid the direct touch of the mug surface with the heating mat, when the picture is too small to cover the whole mug surface.

Adjustion
Pressure To adjust the handle to increase or reduce the pressure.
Time To set the timer to the appropriate time, around 30 seconds.
Temperature Turn the temperature knob to set the appropriate temperature, between 180°C- 200°C
Caution The machine needs 2 minutes break every 60 minutes working period when in mass production.

Problems shooting
Color too light The baking time is not enough, so add more baking time which will get the real color.
Blurred image The baking time is too long, just reduce the baking time will make the image distinct.
Partly color light Caused by the short pressure or the coating is uneven, need to increase the pressure or replace mug with uneven coating.
Blurred image caused by heating mat replace the heating mat.
Scar on image The baking time is much too long, just reduce the baking time largely to remove

Printing colorful custom photo to Mug.. You use it for advertise, gift, etc. Automatic stable temperature.
Mug height/Diameter: 6 inch x 3 inch
Accommodates: 11oz, 15oz, 16oz, mugs & bottles. Fully adjustable & no parts to change
Maximum Pressure
More Heating Element Per Square Inch
Digital Automatic Timer and temperature
Heavy Duty Design
Voltage: 110-120V, Press Temperature: 0-399°C, Time setting:0-99.9H, Power: 380W
Brand New, Individual Wrapped with molded foam package with User's Manual.
Packaging size: 36*36*27CM
Shipping Weight: 10Kg.
We warrant to the original user that this product shall be from all defects in material or workmanship for one year from the date of purchase. This warranty does not apply to any product which has been subject to abuse, misuse, negligence or accident.

Sublimation mug heat press machine

Sublimation mug heat press machine

Sublimation mug heat press machine

(1)The Printer. Choose any normal Ink Jet photo printer and Epson series printer is recommended.
(2)To achieve the best quality of the photo printing, the following printer setting for your reference:
a.Choose the “Best Photo” and the “Photo Quality Ink Jet Paper” under “Main” as shown in figure 1.
b.Click “Advanced” under “Main” to achieve more setting as shown in figure 2.
c.Choose “Mirror Image” under “ Page Layout” as shown in figure 3 while printing photo for ceramic board and metal board, shell board and imitative ceramic necklace etc.

(3)The sublimation ink. Make sure to pull out the color soft plug on the top of the ink cartridges before putting them into the printer. The sublimation ink is easy to dry and better to furnish with one printer until the ink use up.
(4)Ink and printer maintenance.
a.Choose “ Maintenance” under the “Property” of the printer to make maintenance for the printer as shown in figure 4.
b.Use the three buttons on the printer. Ink empty hint. The power light and the ink button are on. (if the ink button keep on flashing, the ink is going to be used up but not yet empty. Replace the empty ink cartridge. Press the ink button. The print head moves to the ink cartridge check position and the power light begins to flash. The ink cartridge indicated by the mark is either empty or low. If more than one ink cartridge is empty or low, the print head moves to the mark. This occurs each time the ink button is pressed until all empty or low ink cartridges have been indicated. Once all of the empty or low ink cartridges have been indicated, the print head moves to the ink cartridge replacement position when the ink button is pressed. Cleaning the print head. Press the ink button for more than three seconds and the printer starts cleaning the print head.
(5)Photo printing. Select the image you need in the computer to print out. Make sure the pixel of the photo is more than 200 to achieve the better heat transferring effect. Please do not touch the printing side of the sublimation paper after printing within 1 minute.
(6)Ink leak. Take tissue to absorb the ink or need to get maintenance from Epson shops.
(7)The printed color is not matched with the original color of the photo. Clean the print head or change a new ink cartridge.
(8)One printer can fill with sublimation ink and normal photo printing ink. But the better way is only fill with one kind of ink in one printer.

Warranty and Maintenance:

1,One-year guarantee.
2,Pressure: Adjust pressure screw clockwise to increase the pressure, counter clockwise to decrease the pressure
3,Time: Check and adjust the position of the jiggle switch in the rear machine case if the buzzer not warn or keep warning when time is out.
4,If press the pressure handle,the handle would be spring back automatically, please adjust the adjusting screw downward. After finished the printing, the handle may be too heavy to hold up, please adjust the adjusting screw upward.
5,Please check the circuit while the heat board is not available after the machine was on several minutes.
6,The natural life of the Silica Gel Board is 10000 times working.
7,The natural life of the Heat Board is 10000 times working.
8,Please feel free to contact us without any delay if there is any problem in the quality.

Advantage
1.Digital controller, working procedure indication, high veracity;
2.Incorporate heater pipe and heater, safe and durable, equal distributing;

3.Beautiful structure
4.Control timer automatically;
5.Convenient to adjust pressure; suitable to pipelining in the factory

Notice:
1. The machine must be connected with the ground wire!
2. Do not touch the heat board while heating!
3. Do not touch the heat board once finish working as time is needed to cool down.
4. Please keep children away from the machine!
5. Please use the heat insulation glove to pick the finished goods!